Slow Speed Small Solar Tracker Slewing Drive For Dual Axis Solar
Tracking System
Description
Solar panels do not perform as well when the temperature increases,
and roof mounted panels can get very hot due to poor ventilation.
More heat, then less power. The solar time tracker allows for
maximum air movement and cooler panels, meaning more energy and
increased panel life.
The dual axis solar tracker generates up to 40% more electricity
compared with a fixed mount system by positioning the solar PV
panels perfectly with the sun all day long, every single day, in
every season, and every weather condition. With a full 180 degree
east to west and north to south tracking option to let the systems
get maximum production.
It increases safety when it comes harsh conditions like snow,
shower or hurricane. You can put your solar panel array into a
safefy position.
Parameters of SE Series
| Model | Ratio | Rated Output Torque(N.m) | Tilting Torque (N.m) | Holding Torque(N.m) | Axial Load(kN) | Radial Load(kN) | Efficiency | Precision(°) | Self-locking | Weight(kg) |
| 1” | 32:1 | 400 | 1000 | 1800 | 22 | 12 | 40% | ≤0.1 | Yes | 6 |
| 3” | 31:1 | 600 | 1500 | 3000 | 30 | 16 | 40% | ≤0.1 | Yes | 8 |
| 5” | 37:1 | 800 | 6000 | 9200 | 68 | 27 | 40% | ≤0.1 | Yes | 12 |
| 7” | 57:1 | 2000 | 13500 | 13200 | 132 | 58 | 40% | ≤0.1 | Yes | 21 |
| 9” | 61:1 | 4400 | 45000 | 30800 | 340 | 130 | 40% | ≤0.1 | Yes | 49 |
| 12” | 78:1 | 5800 | 54400 | 40560 | 480 | 190 | 40% | ≤0.1 | Yes | 61 |
| 14” | 85:1 | 6550 | 68000 | 54200 | 680 | 230 | 40% | ≤0.1 | Yes | 63 |
| 17” | 102:1 | 9400 | 135600 | 65040 | 980 | 390 | 40% | ≤0.1 | Yes | 105 |
| 21” | 125:1 | 16000 | 203400 | 81000 | 1600 | 640 | 40% | ≤0.1 | Yes | 149 |
| 25” | 150:1 | 21000 | 271160 | 89000 | 2400 | 950 | 40% | ≤0.1 | Yes | 204 |
DC Motor
1. Adopt Dual supporting structure for output shaft so that the max
torque of gearbox is increased a lot.
2. Sun wheel and planetary wheel are connected by spline which
increase the max torque of gearbox and lengthen the life.
3. We use helical gear at input stage which make the noise low anf
run smoothly in high speed. The inner gear ring is separated so that we can make more ratio and
the design is flexible. Gearbox and motor are located by a seam fix by screw in axial which
increase the matching precision and reduce noise.
4. We use rolling pin holder inside planetary wheel.we use rolling
pin grinding instead of sliding grinding so the life of gearbox is
much longer.
5. Double supporting structure; Internal grinding on inner bore of
planetary gears making the inner bore roundness less than
0.003mm;running by rolling instead of sliding; HRC60 gear surface
precision scraping;The adopting of all these technoligies ensure
the super quiet and steady operating and a long life time over
10000 hours.
